On a previous post Somchai asked how to hook up an ST7735 LCD screen to his WeMos D1 Mini and use it with the NodeMCU firmware.
The NodeMCU platform (and compatibles like the WeMos) are a great way to get started in the Internet of Things.
See my Introductory Article for how to get started in IoT with NodeMCU.
Here's how to connect and use this inexpensive LCD screen:.
From your du Pont cable set peel off nine male-to-female cables, I suggest brown,red,orange,yellow,green,blue,purple,white,brown (these are contiguous in my set).
Connect like this at the screen:
- brown to GND
- Red to VCC
- Blue to RESET
- Purple to A0
- Yellow to SDA
- Orange to SCK
- Green to CS
- White to LED+
- Grey to LED-
At the NodeMCU connect like this:
- Brown to GND
- Red to 3V3
- Blue to D0
- Purple to D4
- Yellow to D7
- Orange to D5
- Green to D8
- White to 3V3
- Grey to GND
Building your firmware
Using the NodeMCU cloud build service I made a firmware image that contained the modules I needed:
I installed it using esptool:
chris$ esptool.py --port /dev/tty.nodemcu-DevB write_flash -fs 32m 0x00000 nodemcu-master-17-modules-2016-09-23-22-47-56-float.bin esptool.py v1.1 Connecting... Running Cesanta flasher stub... Flash params set to 0x0040 Writing 520192 @ 0x0... 520192 (100 %) Wrote 520192 bytes at 0x0 in 59.1 seconds (70.4 kbit/s)... Leaving...
And when booted it shows the modules present. You must have SPI, ucg and bit modules, the others are up to you.
NodeMCU custom build by frightanic.com branch: master commit: 8e48483c825dea9c12b37a4db3d034fccbcba0bf SSL: true modules: bit,cjson,file,gpio,http,mqtt,net,node,pwm,rtcmem,rtctime,spi,tmr,uart,ucg,wifi,ws2812 build built on: 2016-09-23 22:46 powered by Lua 5.1.4 on SDK 220.127.116.11(39cb9a32)
Testing your screen
chris$ nodemcu-uploader --port /dev/tty.nodemcu-DevB upload * opening port /dev/tty.nodemcu-DevB with 115200 baud Preparing esp for transfer. Transferring GT_box.lua as GT_box.lua Transferring GT_clip.lua as GT_clip.lua Transferring GT_color_test.lua as GT_color_test.lua Transferring GT_cross.lua as GT_cross.lua Transferring GT_fonts.lua as GT_fonts.lua Transferring GT_gradient.lua as GT_gradient.lua Transferring GT_graphics_test.lua as GT_graphics_test.lua Transferring GT_pixel_and_lines.lua as GT_pixel_and_lines.lua Transferring GT_text.lua as GT_text.lua Transferring GT_triangle.lua as GT_triangle.lua Transferring GraphicsTest.lua as GraphicsTest.lua Transferring HelloWorld.lua as HelloWorld.lua Transferring UcgLogo.lua as UcgLogo.lua All done!
Then run the demo by typing
dofile("GraphicsTest.lua"), or using the GUI or the CLI to invoke it
chris$ nodemcu-uploader --port /dev/tty.nodemcu-DevB file do GraphicsTest.lua opening port /dev/tty.nodemcu-DevB with 115200 baud Executing GraphicsTest.lua dofile("GraphicsTest.lua")
It happens that the
GraphicsTest.lua file defaults to using using the ST7735 screen. If you have a different supported screen, make sure that you select that screen when you build your firmware, and that you edit
GraphicsTest.lua to call the setup routine for your screen.
Connecting a WeMos D1 Mini
If you have a WeMos D1 Mini, the connections are the same:
Using the screen in your own code
In your own code, I've found you can connect blue (reset) to the NodeMCU reset and save a pin.
My setup routine looks like this:
-- setup SPI and connect display function screen_init() -- Hardware SPI CLK = GPIO14 = D5 orange -- Hardware SPI MISO = GPIO12 = D6 (not used) -- Hardware SPI MOSI = GPIO13 = D7 yellow -- CS, D/C, and RES can be assigned freely to available GPIOs local cs = 8 -- GPIO15 = D8 green (pull-down 10k to GND) local dc = 4 -- GPIO2 = D4 purple -- local res = NC -- RST (blue) spi.setup(1, spi.MASTER, spi.CPOL_LOW, spi.CPHA_LOW, 8, 8) -- initialize the matching driver for your display -- see app/include/ucg_config.h --disp = ucg.ili9341_18x240x320_hw_spi(cs, dc, res) disp = ucg.st7735_18x128x160_hw_spi(cs, dc) disp:begin(ucg.FONT_MODE_TRANSPARENT) disp:clearScreen() disp:setColor(255, 255, 255) disp:setColor(1, 255, 0,0) end